- Sebelum mengahiri tutorial ini, perlu diketahui bahwa Senao EnGenius EOC-2610 dapat memancarkan dan menangkap frekuensi 1 - 30 kilometer dalam kondisi bersih dan stabil. Itu juga ada setingan sendiri dengan masuk ke Wireless - Wireless Advanced Setting. Pada Data Rate terdapat pilihan 1Mbps, 2Mbps, 5.5Mbps, 11Mbps dan Auto.
- Downloads 3 Manual and Firmware for EnGenius EOC-2610 Networks Cards. Here's where you can downloads the newest software for your EOC-2610.
- Cara Setting Engenius Eoc-2610 Trinity Messiah Yaoi Bl Game Native Instruments B4ii Keygen Mac Download Ebook Patologi Robbins Edisi 9 Bahasa Indonesia Venus T5 User Manual Aneesh Menon Serial Actor Dt Keygen Logixpro Keygen Flexisign Pro 10 Poser Download Autocad Electrical 2013.
- Engenius Eoc 2610 Price
- Cara Setting Engenius Eoc 2610 Manual
- Engenius Eoc 2610 Manual
- Engenius
- Cara Setting Engenius Eoc 2610 Setup
From DD-WRT Wiki
|
THX to malcolmchng
- Ubiquity Nanostation2 clone with better hardware.
- 600mW Wireless Power.
- 24V PoE.
- SuperG 108Mbps Support.
- Internal dual 10dBi panel.
[edit]Internal
[edit]External
Engenius Eoc 2610 Price
7. Please test the server http://192.168.1.11/ DD-WRT_newimage.bin; it may take a few seconds before the page is completely loaded by your web-browser.
10. Under the console prompt type in the following commands in REDtogether with the address link
how to configure Engenius eoc2611P/EOC1650 as point to point or point to multipoint bridge
Point to Point or Point to Multi-Point:
Using the EnGenius 2611P/1650 series you can create a wireless link between two buildings or multiple buildings. Below describes a building to building connection. To add more than two buildings you will need to add more client bridge units. Settings will be dependent on your network infrastructure. Please read the full document to have complete understanding of the setup.
1st UNIT:
1. Change mode to Access Point Mode, under system, system properties apply
2. Set static IP address, Subnet Mask, Gateway, under system, IP Settings then IP addresses depend on your local area network. Normally this information can be found by accessing your router (Gateway). Choose a static IP that is outside the DHCP range on your network and not being used by another device, use ping to check.
3. Set SSID desired Channel under Wireless, wireless network SSID is determined by the admin. EnGenius recommends using channels 1, 6 or 11.
4. Set output power to 28dBm for maximum range under wireless, wireless advanced
5. Security can be set under Wireless, wireless security. (test without security first)
2nd UNIT: E
1. Keep mode in Client Bridge Mode
2. Set static IP address, Subnet Mask, Gateway, under system, IP Settings3. Set output power to 28dBm for maximum range under wireless, wireless advanced
4. Set SSID to the same settings as the 1st unit (AP) under Wireless, wireless network. use site survey utility to find AP then click on MAC address in the survey tool. check box perfer BSSID on bridge.
5. if security is enable on the AP the bridge will ask for the key
For point to multipoint use a omni directional antenna on the AP then add additional eoc-2611P bridge units configured as above.
Cara Setting Engenius Eoc 2610 Manual
For point to multipoint links up to 3 miles use a eoc-2611P at the central location with 8.5dBi omni directional antenna and SMA pigtail connector
For the remote locations just add another eoc-2611P unit
Engenius Eoc 2610 Manual
Click here for our price
Engenius
Have questions please post to this thread in the forums